...
This guide is relevant for the following models:
| Multimedia |
|---|
| name | Lantronix.mp4 |
|---|
| width | 720 |
|---|
| height | 480 |
|---|
|
| Lantronix UDS2100 (2-port) | Lantronix EDS4100 (4-port) |
Image Removed 
Image Removed
 Image Added New model has password. Passowrd is last 8 of the ID found on back.
|
 Image Added
|
| Info |
|---|
IMPORTANT NOTE:
If you are installing Do NOT simultaneously install more than one Lantronix device at a location, they must be installed ONE AT A TIMEthe same location. Default IP conflicts may occur if set up at the same time. |
...
GET INSTALLATION FILES:
- Go to: \\hq-file1\Shared\Install\NorthStar\NorthStar Order Entry\NSOE Peripherals\Lantronix - Serial to
...
- IP
- Copy the following files from the site to your local desktop where the software will be installed:
- Device Installer
| View file |
|---|
| name | DeviceInstaller-4402-SA.zip |
|---|
| height | 250 |
|---|
|
| View file |
|---|
| name | DeviceInstaller-4402-Web.zip |
|---|
| height | 250 |
|---|
|
- Secure Com Port Redirector
After transferring these two folders to the site on which you're installing the hardware, you will install them.
| View file |
|---|
| name | setup_cpr_x86x64cd_4.3.0.3.zip |
|---|
| height | 250 |
|---|
|
- Open the Device Installer folder
|
...
- Run setup_di_x86x64cd_4.4.0.
|
...
- 2
- When installation is complete,click
|
...
- the Device Installer program
|
...
- .
- Any Lantronix devices on the network should appear.
|
...
...
- (See screenshot.) If they do not, click Search.
- Select your device
- Click Assign IP. You can assign an IP automatically or assign a static IP
|
...
Step 2:
|  Image Added
|
| |
- Open the Secure Com Port Redirector folder
|
...
- Run setup_cpr_x86x64cd_4.3.0.3 to install the 2nd program
|
...
- . This allows port assignment to the Lantronix boxes.
|
...
- CPR Manager should now be installed.
(IMPORTANT NOTE:
|
...
- Inaccessible ports will be automatically detected on the left side under the Com Ports section)
|
...
.png?version=2&modificationDate=1432849189283&cacheVersion=1&api=v2&width=660) Image Added
|
...
...
...
- currently on the network will appear in the lower pane.
- Double-click the
|
...
- device name
- The com ports available for the device will be shown. In the
|
...
- example at right, a 2-Port (.200) and
|
...
...
| .png?version=2&modificationDate=1432849458375&cacheVersion=1&api=v2&width=700) Image Modified
|
...
- on the top left to display all
|
...
...
|  Image Modified
|
...
...
...
...
To remove the virtual ports, |
...
deselect the virtual ports |
...
and click OK. Click Save at the top) |  Image Modified
|
- After this, it will display the ports you just flagged on the left side under Com Ports. They will be highlighted in red with the word New to indicate they were just added.
...
- The new ports are now highlighted in red and display (New) next to them.
|  Image Added
|
- Select the first new Com. Its settings will appear in the right pane.
|
...
...
...
- Host and TCP Port section.
|  Image Modified
|
...
...
...
- field below the Host column
|
...
- In the Host field, type the IP address of your device
|
...
...
...
be 10001; in succession, the next would be 10002, 10003, 10004, etc. This is determined
|
...
...
...
...
- The edited virtual port is now the first physical port
|
...
...
- Lantronix Serial-to-Ethernet Device. In the example, Com 7 is now
|
...
- physical Port 1 (TCP Port 10001).
|
...
IMPORTANT: If you attempt to double-click to add
|
...
...
...
...
...
...
...
...
...
. To show the available TCP Ports, expand the list. To expand the list, click on an inaccessible Com port or away from the box |
...
. |  Image Modified
|
...
- Click on the next virtual com port you're going to assign.
|
...
...
...
...
- Repeat the previous steps; scroll down
|
...
...
...
- Service section of the Com's settings.
- Click
|
...
...
...
- column
- Manually add the device's IP
|
...
- address under Host then its second TCP Port, 10002.
|  Image Modified
|
...
- Repeat the process until you have added all of your ports.
- Click Save at the top.
- When finished,
|
...
- go to ECM > Peripherals to add the ports to their corresponding devices.
Example: If a Customer Display Unit is attached to physical port 1 of the Lantronix box and Com 7 is associated with physical port 1, enter Com 7 in the Customer Display Unit's settings under Peripherals. - Linked devices can now communicate with the server.
|  Image Added
|
- When setting up a Lantronix and CPR for use with a VX805 credit card terminal there are two additional drivers that need to be installed on the Order Entry server in order for the VX805 to be able to communicate with the server and CPR manager.
- These drivers are normally associated with NetEPay but they MUST be installed even if the site is not using EMV (NetEPay is only needed when site is using EMV)
- The drivers can be downloaded from the Datacap Systems page: http://www.datacapepay.com/epay50/2946/
- Make sure you are getting the correct drivers and that they are the most recent version
- Once the drivers have been installed the Order Entry server will need to be rebooted and the payment device reinitialized from the iPad once everything is back up.
|  Image Added
 Image Added |
| Multimedia |
|---|
| name | Lantronix.mp4 |
|---|
| width | 600 |
|---|
| height | 400 |
|---|
|